Motec E816 User Manual

MoTeC E888/816 Manual Contents Introduction... 1 Overview...

8 Outputs

MoTeC Outputs 9 The tab for Expander Output configuration can be found under the Dash Manager menu item ‘Functions – Auxiliary Outputs’.

10 Outputs The E8xx outputs can now be configured the same way as the ADL Auxiliary outputs by selecting an output and then setting the control chann

MoTeC E8xx Diagnostic Information 11 E8xx Diagnostic Information Additional status information is available from the E8xx along with the state of t

12 E8xx Diagnostic Information Test Analogue Inputs It is possible to view the current ‘live’ voltages on the expander’s analogue inputs using a PC

MoTeC E8xx Diagnostic Information 13 100% duty cycle corresponds to the output fully On (Low Voltage), 0% duty cycle corresponds to the output full

14 Communications Communications CAN The CAN bus is used for PC communications during testing, calibration and firmware upgrades, and for communicati

MoTeC Appendices 15 Appendices Appendix A: General Specifications Physical and Environmental Case Size 99 x 105mm x 40mm Weight E888 310g

16 Appendices Appendix B: Input Characteristics K-Type thermocouple Inputs (E888) Range -200 to 1250°C Resolution 1°C Accuracy (excluding

MoTeC Appendices 17 Resolution 1°C Accuracy -10 to 70degC measured temperature, +/- 1°C + Sensor accuracy Digital Inputs (Schmitt Trigger) Pullup

18 Appendices Appendix C: Output Characteristics Outputs Current per output when using the given number of outputs: • 1 Output 3.2A • 2 Outputs 2.3A

MoTeC Appendices 19 Appendix D: CAN Wiring – Multiple Device The CAN bus should consist of a twisted pair trunk with 100R (0.25Watt) terminating resi

20 Appendices Appendix E: E8xx to ADL Wiring See pin list Ground E8xx Bat -ADL 7See pin list Power Bat +8B24 / 47 CAN-LO CAN-LO73 or 75B23 / 54 CAN-

MoTeC Appendices 21 Appendix F: E8xx to M800 Wiring Note that this also applies to the M400, M600 and M880 ECUs. See pin list Ground E8xx ECU See pi

22 Appendices Appendix G: E888 Pin List by Pin Number The E888 uses a 34 + 26 pin connector pair with the following pin-out: Pin Function Pin Fu

MoTeC Appendices 23 Appendix H: E816 Pin List by Pin Number The E816 uses a 66 pin autosport connector with the following pin-out: Pin Function (E81

24 Appendices Appendix I: E816 Connector Mating Connector Deutsch : AS6-18-35SN Wire Wire to suit connector : 22# Tefzel, Mil Spec : M22759/16-22 Cri

MoTeC Notes 25

26 Notes

MoTeC Notes 27

MoTeC Introduction 1 Introduction This manual describes the functions and specifications of the E888/E816 expander modules and their configuration fo

28 Notes

2 Overview Overview The E888 has the following inputs and outputs: • 8 Analog voltage inputs (AV 1-8) • 8 Thermocouple inputs (TC 1-8) • 2 Cold ju

MoTeC Inputs 3 Inputs E888 Thermocouple Inputs (TC1 – TC8) The E888 has eight calibrated and compensated type K (-200 to 1250ºC) thermocouple inputs.

4 Inputs Digital Inputs (DIG1 – DIG 4) DIG1 to DIG4 may be used to measure frequency. The frequency measurement range is approximately 1Hz to 5000Hz.

MoTeC Inputs 5

6 Inputs E888 Thermocouples Thermocouple inputs 1 – 8 correspond to Expander Analog inputs ExTC1 to ExTC8. The calibration used for these inputs is “

MoTeC Outputs 7 Outputs Both the E888 and E816 include 8 Auxiliary Outputs that are individually controllable for frequency and duty cycle. They are